Radio Shack Cordless Telephone ET 1112 User Guide

43-1112.fm Page 1 Monday, September 13, 1999 5:08 PM  
Cat. No. 43-1112  
OWNER’S MANUAL  
Please read before using this equipment.  
ET-1112  
900 MHz Digital Spread Spectrum  
Cordless Phone  
 
43-1112.fm Page 3 Monday, September 13, 1999 5:08 PM  
Important:  
This symbol is intended to inform  
you that important operating and  
maintenance instructions are  
included in the literature accom-  
panying this product.  
• Cordless phones such as this one  
require AC power to operate. When  
the AC power is off, you cannot dial  
out or receive incoming calls using  
your ET-1112. To be safe, you  
should also have a phone that does  
not need AC power to operate (not a  
cordless phone) so you can still  
make and receive calls if there is an  
AC power failure.  
!
READ THIS BEFORE  
INSTALLATION  
We have designed your phone to con-  
form to federal regulations and you can  
connect it to most phone lines. However,  
each device that you connect to the tele-  
phone line draws power from the line.  
We refer to this power draw as the  
phone’s ringer equivalence number, or  
REN. The REN is on the bottom of your  
phone.  
• When AC power is lost, the ET-1112  
loses the security access-protection  
code connection between the base  
and the handset. When power is  
restored, put the handset on the  
base briefly to restore this connec-  
tion so you can use the handset.  
If you use more than one phone or other  
device on the line, add up all the RENs.  
If the total is more than five (three in ru-  
ral areas), your phones might not ring. If  
ringer operation is impaired, remove one  
of the devices from the line.  
WARNING: To reduce the risk of fire or  
shock hazard, do not expose this product to rain  
or moisture.  
CAUTION  
RISK OF ELECTRIC SHOCK.  
!
DO NOT OPEN.  
CAUTION: TO REDUCE THE RISK OF  
ELECTRIC SHOCK, DO NOT REMOVE  
COVER OR BACK. NO USER-SERVICE-  
ABLE PARTS INSIDE. REFER SERVICING  
TO QUALIFIED PERSONNEL.  
This symbol is intended to alert  
you to the presence of uninsu-  
lated dangerous voltage within  
the product’s enclosure that might  
be of sufficient magnitude to con-  
stitute a risk of electric shock. Do  
not open the product’s case.  
3
 
43-1112.fm Page 4 Monday, September 13, 1999 5:08 PM  
FCC STATEMENT  
Your telephone complies with Part 68 of  
FCC Rules. Upon request, you must  
provide the phone’s FCC registration  
number and REN to your telephone  
company. These numbers are on the  
bottom of the base.  
Note: You must not connect your tele-  
phone to:  
• coin-operated systems  
• party-line systems  
• most electronic key phone systems  
4
 
43-1112.fm Page 5 Monday, September 13, 1999 5:08 PM  
INSTALLATION  
2. Plug the modular cord’s other end  
into a modular phone line jack.  
SELECTING A LOCATION  
You can place the phone’s base on a  
desk top or table, or mount it on a wall.  
Select a location that is:  
3. Insert the supplied AC adapter’s  
barrel plug into the DC IN 9V jack on  
the back of the base.  
• near an accessible AC outlet  
• near a telephone line jack  
• out of the way of normal activities  
• away from electrical machinery,  
electrical appliances, metal walls or  
filing cabinets, wireless intercoms,  
alarms, and room monitors  
4. Route the adapter’s cord through  
the strain relief slot on the base.  
• away from other cordless phones  
The base’s location affects the hand-  
set’s range. If you have a choice of sev-  
eral locations, try each to see which  
provides the best performance.  
Caution: The supplied RadioShack AC  
adapter was designed specifically for  
your ET-1112. Use only the supplied  
adapter.  
5. Plug the adapter into a standard AC  
outlet.  
On a Desk Top  
6. Lift the base’s antenna to an upright  
position.  
Follow these steps when you place the  
base on a desk, shelf, or table.  
1. Plug one end of the supplied long  
modular cord into the TEL LINE jack  
on the back of the base.  
On a Wall Plate or Wall  
1. Plug one end of the supplied short  
modular cord into the TEL LINE jack  
on the back of the base as in “On a  
Desk Top,” Step 1.  
2. Insert the supplied AC adapter’s  
barrel plug into the DC IN 9V jack as  
in “On a Desk Top,” Step 3.  
5
 
43-1112.fm Page 6 Monday, September 13, 1999 5:08 PM  
3. Route the adapter and modular  
cords through the grooves on the  
bottom of the base.  
7. Lift the base’s antenna to an upright  
position.  
Note: To mount the ET-1112 directly on  
a wall, you need two screws (not sup-  
plied) with heads that fit into the keyhole  
slots on the bottom of the base.  
Follow the steps under “On a Wall Plate  
or Wall” on Page 5, then apply these ad-  
ditional instructions for placement on a  
wall.  
1. Drill two holes 315/16  
inches (100 mm)  
apart. Then thread  
a screw into each  
4. Plug the modular cord’s other end  
into the wall plate jack, then align  
the base’s keyhole slots with the  
wall plate studs and slide the base  
downward to secure it.  
5/16  
Inch  
315/16  
Inch  
hole, letting the  
heads extend about  
5/16 inch (8 mm)  
from the wall.  
2. Plug one end of the supplied long  
modular cord into the TEL LINE jack  
on the back of the base.  
3. Align the base’s keyhole slots with  
the mounting screws and slide the  
base downward to secure it.  
5. Plug the adapter into a standard AC  
outlet.  
6. Press and lift out the handset  
holder, rotate it 180°, then snap it  
back into place so it holds the hand-  
set.  
Handset  
Holder  
6
 
43-1112.fm Page 7 Monday, September 13, 1999 5:08 PM  
To charge the battery pack, simply place  
the handset on the base. The CHARGE/  
IN USE indicator on the base lights.  
CONNECTING AND  
CHARGING THE BATTERY  
PACK  
The phone comes with a rechargeable  
nickel-cadmium battery pack in the  
handset, but not connected. Before us-  
ing your phone, you must connect the  
battery pack and then charge it for about  
24 hours.  
1. Press down and slide the battery  
compartment cover in the direction  
of the arrow to remove it.  
Recharge the battery pack when the  
handset beeps and the TALK/BATT indi-  
cator flashes.  
Important: Be sure the battery pack is  
properly connected before you try to  
charge it. The CHARGE/INUSE indica-  
tor lights when the handset is on the  
base, even if the battery pack is not con-  
nected.  
2. Unfasten the battery retainer strap  
and lift the battery pack out of the  
compartment. Plug the battery  
pack’s connector into the socket in  
the compartment. The connector fits  
only one way.  
Notes:  
• When you first use the phone after  
charging or recharging the battery  
pack, the phone might not work and  
you might hear an error tone. If this  
happens, return the handset to the  
base for a few seconds.  
• About once a month, fully discharge  
the battery pack by keeping the  
handset off the base until the TALK/  
BATT indicator flashes. Otherwise,  
the battery pack loses its ability to  
fully recharge.  
3. Put the battery pack in the compart-  
ment and fasten the battery retainer  
strap.  
4. Replace the cover.  
7
 
43-1112.fm Page 8 Monday, September 13, 1999 5:08 PM  
• Using a pencil eraser, clean the  
charging contacts on the handset  
and the base about once a month.  
SETTING THE DIALING  
MODE  
Set PULSE-TONE on the back of the  
base for the type of service you have. If  
you are not sure which type you have,  
once the battery pack is fully charged,  
do this test.  
1. Be sure PULSE-TONE is set to TONE.  
2. Lift the handset, press TALK, and lis-  
ten for a dial tone.  
3. Press any number other than 0.  
• If the TALK/BATT indicator does not  
light and the phone does not work,  
recharge the battery pack. (The bat-  
tery power might be too low to light  
the indicator.)  
Note: If your phone system requires  
that you dial an access code (9, for  
example) before you dial an outside  
number, do not press the access  
code either.  
• If the battery pack becomes weak  
during a call, you hear a beep and  
the TALK/BATT indicator flashes  
every 4 seconds. Recharge the bat-  
tery pack.  
If the dial tone stops, you have  
touch-tone service. Leave PULSE-  
TONE set to TONE.  
If the dial tone continues, you have  
pulse service. Set PULSE-TONE to  
PULSE.  
• If the battery pack is completely dis-  
charged, the handset loses the  
security access-protection code. To  
reset the code, place the handset on  
the base and charge the battery  
pack.  
• The supplied battery pack should  
last for about a year. When the bat-  
tery pack loses its ability to fully  
recharge, order a replacement bat-  
tery  
pack  
from  
your  
local  
RadioShack store (see “Replacing  
the Battery Pack” on Page 18).  
8
 
43-1112.fm Page 9 Monday, September 13, 1999 5:08 PM  
SETTING THE RINGER’S  
TONE AND VOLUME  
You can set four ringer tones and a high  
and low volume for each.  
To change the tone, lift the handset and  
press FLASH. Then, enter the ringer  
tone number (1–4) using the number  
keys. The selected tone sounds briefly.  
FLASH  
To hear and change the ringer volume  
setting, press or  
.
9
 
43-1112.fm Page 10 Monday, September 13, 1999 5:08 PM  
OPERATION  
MAKING AND RECEIVING  
CALLS  
SETTING THE HANDSET  
VOLUME  
To make a call, lift the handset and  
press TALK. The TALK indicator on the  
handset and the IN USE indicator on the  
base light. When you hear a dial tone,  
dial the number.  
You can choose one of four volume set-  
tings — low, medium, high, or maximum  
— for the handset. To change the vol-  
ume, press or during a call.  
USING REDIAL  
TALK  
You can quickly dial the last number di-  
aled. When you hear a dial tone, simply  
press REDIAL.  
Notes:  
• The redial memory holds up to 32  
digits, so you can redial long-dis-  
tance as well as local numbers.  
To answer a call, lift the handset if nec-  
essary then press TALK.  
The ET-1112 scans 20 channels (fre-  
quency pairs used between the base  
and the handset) and automatically se-  
lects a clear channel each time you  
make or receive a call.  
• The redial memory also holds pause  
entries. See “Entering a Pause” on  
Page 13.  
Note: If the handset is too far from the  
base, the channel might not be clear.  
Move closer to the base and try making  
the call again.  
MUTE  
REDIAL  
To end a call, place the handset on the  
base or press TALK.  
Note: If you press TALK to hang up and  
the phone does not disconnect, press  
TALK again while holding the handset  
closer to the base, or place the handset  
on the base.  
USING MUTE  
To talk to someone in the room without  
the person on the other end of the  
phone line hearing your conversation,  
press MUTE. The TALK/BATT indicator  
flashes.  
10  
 
43-1112.fm Page 11 Monday, September 13, 1999 5:08 PM  
Press MUTE again to resume your  
phone conversation.  
PAGING  
To page the person who has the hand-  
set or to locate the handset when the  
phone is not in use, press PAGE on the  
base. The handset beeps for about 15  
seconds. To stop the beeping sooner,  
press TALK on the handset twice or  
PAGE on the base.  
USING FLASH  
FLASH performs the electronic equiva-  
lent of a switchhook operation for spe-  
cial services, such as Call Waiting.  
For example, if you have Call Waiting,  
press FLASH to answer an incoming call  
without disconnecting the current call.  
Press FLASH again to return to the first  
call.  
Note: If you do not have any special  
phone services, pressing FLASH might  
disconnect the current call.  
PAGE  
USING TONE SERVICES  
ON A PULSE LINE  
Some special services, such as bank-  
by-phone, require tone signals. If you  
have pulse service, you can still use  
these special tone services by following  
these steps.  
Notes:  
• Make sure you press TALK twice to  
stop the handset from beeping. If  
you press TALK only once, you get a  
dial tone.  
1. Be sure PULSE-TONE is set to  
PULSE.  
• If you receive a call while the page is  
sounding, the handset stops beep-  
ing and starts ringing.  
2. Dial the service’s main number.  
3. When the service answers, press  
TONE ( ). Any additional numbers  
you dial are sent as tone signals.  
4. After you complete the call, return  
the handset to the base or press  
TALK. The phone automatically  
resets to the pulse mode.  
11  
 
43-1112.fm Page 12 Monday, September 13, 1999 5:08 PM  
• Each tone or pause entry uses  
one digit of memory.  
MEMORY DIALING  
The ET-1112 can store three telephone  
numbers in speed dial memory, and you  
can dial any one of these numbers by  
pressing a single button. You can also  
store up to 20 more numbers that you  
can dial by entering a two-digit memory  
location number.  
4. To assign the number to a speed  
dial button, press MEM, then press a  
speed dial button (M1M3).  
To store the number in a standard  
memory location, press MEM, then  
enter the two-digit memory location  
number (0120).  
The handset sounds a long beep to  
indicate that the number is stored.  
Storing a Number in Memory  
Note: An error tone sounds and the  
phone exits the storing process if you  
wait more than 30 seconds between  
each key press.  
5. For each stored number, write the  
person’s or company’s name next to  
the appropriate location number on  
the supplied memory directory  
sticker. Peel the backing off the  
sticker and attach it to the phone.  
1. Lift the handset.  
2. Press MEM. The TALK/BATT indica-  
tor blinks.  
MEM  
To replace a stored number, simply  
store a new one in its place.  
3. Enter the number and any tone  
mode changes or pause entries  
(see “Entering a Pause”).  
To delete a stored number, lift the  
handset and press MEM twice, then  
enter the memory location number  
(0120) or press the speed dial but-  
ton (M1M3) you want to clear. The  
handset sounds a long beep to sig-  
nal that the memory location is  
clear.  
Notes:  
• Each number you store can be up  
to 16 digits long.  
• If you try to enter more than 16  
digits, the phone sounds an error  
tone and exits the storing pro-  
cess. Start over from Step 2.  
12  
 
43-1112.fm Page 13 Monday, September 13, 1999 5:08 PM  
Dial the service’s main number first.  
Then, at the appropriate place in the  
call, press the memory location button  
(M1M3), or press MEM and enter the  
memory location number (0120) for the  
stored information.  
Entering a Pause  
In some telephone systems, you must  
dial an access code (9, for example) and  
wait for a second dial tone before you  
can dial an outside number. You can  
store the access code with the phone  
number. However, you should also store  
a pause after the access code to allow  
the outside line time to connect. To en-  
ter a 2-second pause, press REDIAL.  
For a longer pause, press REDIAL addi-  
tional times.  
Testing Stored Emergency  
Numbers  
If you store an emergency service’s  
number (police department, fire depart-  
ment, ambulance) and you choose to  
test the stored number, make the test  
call during the late evening or early  
morning hours to avoid peak demand  
periods. Also, remain on the line to ex-  
plain the reason for your call.  
Dialing a Memory Number  
To dial a number assigned to a speed  
dial button, simply press the button (M1–  
M3) for the number you want to dial.  
(You do not need to press TALK first.)  
USING A HEADSET  
To dial a number stored in a standard  
memory location, press TALK. When you  
hear a dial tone, press MEM and enter  
the two-digit memory location number  
for the number you want to dial.  
You can talk with hands-free conve-  
nience using an optional headset that  
3
has a /32-inch (2.5-mm) plug. Contact  
your local RadioShack store for a suit-  
able headset.  
Note: If you select an invalid memory lo-  
cation (for example 3 instead of 03), the  
phone sounds an error tone. Press MEM  
again and re-enter the memory location  
number.  
To connect the headset, open the rub-  
ber cover marked  
on the side of the  
handset, then insert the headset’s plug  
into the jack.  
Notes:  
Chain-Dialing Service Numbers  
• Connecting a headset disconnects  
the handset’s earpiece and micro-  
phone.  
For quick recall of numbers for special  
services (such as alternate long dis-  
tance or bank-by-phone), store each  
group of numbers in its own memory lo-  
cation.  
or on the handset also controls  
the connected headset’s volume.  
13  
 
43-1112.fm Page 14 Monday, September 13, 1999 5:08 PM  
• If you place the handset on the base  
while the headset is connected, be  
sure the handset seats properly.  
With a headset connected, you can  
make or answer calls as usual using the  
keys on the handset.  
You can use a handset holder (available  
from your local RadioShack store) to  
hang the handset on your belt for great-  
er convenience.  
When you finish using the headset, dis-  
connect it and close the rubber cover to  
protect the jack.  
14  
 
43-1112.fm Page 15 Monday, September 13, 1999 5:08 PM  
TROUBLESHOOTING  
We do not expect you to have any problems with your ET-1112, but if you do, the fol-  
lowing suggestions might help.  
Problem  
Suggestion  
The phone does not work or  
works poorly.  
Be sure the base’s phone line cord and AC adapter are  
correctly and securely connected, and the battery pack  
in the handset is charged.  
Return the handset to the base for a few seconds to  
reset the security access-protection code.  
The handset stops working or  
works poorly during a call.  
Move the handset closer to the base.  
Lift the base’s antenna to a fully upright position.  
Be sure the handset’s battery pack is charged. (If the  
battery pack power is too low, it does not have enough  
power to light the LOW BATT indicator.)  
Low volume or unusual sounds. Someone has picked up another phone on the same  
line. Hang up the other phone.  
Severe noise interference.  
Keep the handset and base away from computers,  
remote control toys, wireless microphones, alarm sys-  
tems, intercoms, room monitors, fluorescent lights, and  
electrical appliances.  
Move to another location or turn off the source of inter-  
ference.  
Hang up and redial the number.  
The phone cannot be operated  
at a useful distance from the  
base because the signal  
becomes weak or noisy (hand-  
set’s range has decreased).  
Lift the base’s antenna to a fully upright position.  
Be sure neither the handset or base antenna is touching  
a metal surface.  
Recharge the battery pack.  
The handset battery pack does  
not charge.  
Check the charging contacts on the handset and base. If  
they are dirty, clean them with a pencil eraser.  
Be sure the battery pack is properly connected.  
Be sure the handset is properly seated on the base.  
15  
 
43-1112.fm Page 16 Monday, September 13, 1999 5:08 PM  
Problem  
Suggestion  
Handset does not ring or  
receive a page.  
Lift the base’s antenna to a fully upright position.  
Move the handset closer to the base.  
Move the base away from other electrical devices.  
Recharge the battery pack.  
If you still have problems, disconnect the phone. If other phones on the same line  
work properly, the fault is in this phone or its installation. If you cannot find the prob-  
lem, take your ET-1112 to your local RadioShack store for assistance.  
16  
 
43-1112.fm Page 17 Monday, September 13, 1999 5:08 PM  
CARE AND MAINTENANCE  
Your RadioShack ET-1112 900 MHz Digital Spread Spectrum Cordless Telephone  
is an example of superior design and craftsmanship. The following suggestions will  
help you care for your ET-1112 so you can enjoy it for years.  
Keep the ET-1112 dry. If it gets wet, wipe it dry immediately. Liquids  
might contain minerals that can corrode the electronic circuits.  
Use and store the ET-1112 only in normal temperature environments.  
Temperature extremes can shorten the life of electronic devices, dam-  
age batteries, and distort or melt plastic parts.  
Keep the ET-1112 away from dust and dirt, which can cause premature  
wear of parts.  
Handle the ET-1112 gently and carefully. Dropping it can damage circuit  
boards and cases and can cause the ET-1112 to work improperly.  
Use only fresh batteries of the required size and recommended type.  
Batteries can leak chemicals that damage your ET-1112’s electronic  
parts.  
Wipe the ET-1112 with a damp cloth occasionally to keep it looking new.  
Do not use harsh chemicals, cleaning solvents, or strong detergents to  
clean the ET-1112.  
Modifying or tampering with the ET-1112’s internal components can cause a mal-  
function and might invalidate its warranty and void your FCC authorization to operate  
it. If your ET-1112 is not performing as it should, take it to your local RadioShack  
store for assistance. If the trouble is affecting the telephone lines, the phone compa-  
ny can ask you to disconnect your ET-1112 until you have resolved the problem.  
17  
 
43-1112.fm Page 18 Monday, September 13, 1999 5:08 PM  
• Be careful not to short the battery  
pack by touching the connector’s  
pins with conducting materials, such  
as rings, bracelets, and keys. The  
battery pack or conductor might  
overheat and burn.  
REPLACING THE  
BATTERY PACK  
If you follow the instructions in “Connect-  
ing and Charging the Battery Pack” on  
Page 7, the battery pack should last  
about one year. If the battery pack does  
not hold a charge for more than 2 hours  
after an overnight charge, replace it with  
a new 3.6-volt, 600 mAh battery pack  
with a connector that fits the socket in  
the battery compartment. You can order  
a replacement battery pack through your  
local RadioShack store.  
If you have trouble replacing the battery  
pack, take the phone to your local Ra-  
dioShack store for assistance.  
Important: This tele-  
phone can use nickel-  
cadmium rechargeable  
batteries. At the end of a  
nickel-cadmium battery's  
useful life, it must be re-  
0
0
8
3
4
Install the new battery pack as de-  
scribed below, then charge it for about  
24 hours.  
cycled or disposed of properly. Contact  
your local, county, or state hazardous  
waste management authorities for infor-  
mation on recycling or disposal pro-  
grams in your area or call 1-800-843-  
7422. Some options that might be avail-  
able are: municipal curbside collection,  
drop-off boxes at retailers such as your  
local RadioShack store, recycling collec-  
tion centers, and mail-back programs.  
1. Press down and slide off the cover.  
2. Unfasten the battery retainer strap  
and lift the battery pack out of the  
compartment, then gently pull on  
the battery connector to disconnect  
it.  
3. Insert the new battery pack’s con-  
nector into the socket in the com-  
partment, place the battery pack  
into the compartment, and fasten  
the battery retainer strap.  
THE FCC WANTS YOU TO  
KNOW  
4. Replace the cover.  
In the unlikely event that your phone  
causes problems on the phone line, the  
phone company can temporarily discon-  
tinue your service. If this happens, the  
phone company attempts to notify you in  
advance. If advance notice is not practi-  
cal, the phone company notifies you as  
soon as possible and advises you of  
your right to file a complaint with the  
FCC.  
Cautions:  
You must use a replacement battery  
pack of the same size and type.  
• Do not dispose of the battery pack  
in a fire because it might explode.  
• Do not open or mutilate the battery  
pack.  
18  
 
43-1112.fm Page 19 Monday, September 13, 1999 5:08 PM  
Also, the phone company can make  
changes to its lines, equipment, opera-  
tions, or procedures that could affect the  
operation of this telephone. The tele-  
phone company notifies you of these  
changes in advance, so you can take  
the necessary steps to prevent interrup-  
tion of your telephone service.  
LIGHTNING  
Your telephone has built-in lightning pro-  
tection to reduce the risk of damage  
from surges in telephone line and power  
line current. This lightning protection  
meets or exceeds FCC requirements.  
However, lightning striking the tele-  
phone or power lines can damage your  
telephone.  
Your phone might cause TV or radio in-  
terference even when it is operating  
properly. To determine whether your  
phone is causing the interference, turn  
off your phone. If the interference goes  
away, your phone is causing it. Try to  
eliminate the interference by:  
Lightning damage is not common. Nev-  
ertheless, if you live in an area that has  
severe electrical storms, we suggest  
that you unplug your phone during  
storms to reduce the possibility of dam-  
age.  
• moving your phone away from the  
receiver  
• connecting your phone to an AC  
outlet that is on a different electrical  
circuit from the receiver  
• contacting your local RadioShack  
store for help  
If you cannot eliminate the interference,  
the FCC requires that you stop using  
your phone.  
Some cordless telephones operate on  
frequencies that might cause interfer-  
ence to nearby TVs and VCRs. To mini-  
mize or prevent such interference, the  
base of the cordless telephone should  
not be placed near or on top of a TV or  
VCR.  
19  
 
43-1112.fm Page 20 Monday, September 13, 1999 5:08 PM  
Limited One-Year Warranty  
This product is warranted by RadioShack against manufacturing defects in material and workman-  
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned  
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-  
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING  
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED  
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED  
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-  
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY  
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-  
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUD-  
ING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF  
TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL,  
OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSI-  
BILITY OF SUCH DAMAGES.  
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-  
cidental or consequential damages, so the above limitations or exclusions may not apply to you.  
In the event of a product defect during the warranty period, take the product and the RadioShack  
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-  
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and  
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase  
price. All replaced parts and products, and products on which a refund is made, become the prop-  
erty of RadioShack. New or reconditioned parts and products may be used in the performance of  
warranty service. Repaired or replaced parts and products are warranted for the remainder of the  
original warranty period. You will be charged for repair or replacement of the product made after the  
expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,  
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or  
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs  
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as  
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs  
of product removal, installation, set-up service adjustment or reinstallation.  
This warranty gives you specific legal rights, and you may also have other rights which vary from  
state to state.  
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102  
We Service What We Sell  
04/99  
RadioShack  
A Division of Tandy Corporation  
Fort Worth, Texas 76102  
UCZZ01635BZ  
09A99  
Printed in the Philippines  
 

Ratoc Systems Network Card PCIU2 User Guide
Raypak Boiler Commercial Space Heating and Domestic Water User Guide
Roberts Gorden Saw 60007 User Guide
Roland DJ Equipment M 300 User Guide
Roland Projection Television CR 8000 User Guide
Runco Headphones CW 95DHD User Guide
Samsung Computer Drive HX M250UAB User Guide
Sanyo Battery Charger KR 1000SCL User Guide
Scag Power Equipment Lawn Mower STC48V 26BS, STC52V 23BV, STC61V 23BV User Guide
Sears Vacuum Cleaner 11317066 User Guide