QUICK SETUP GUIDE
1 Attach the TV brackets
2 Install the wall plate
RF-TVMLPT03
Option 1: Attaching to a ꢀat
Option 1: Installing to a wood stud wall
Caution: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts.
Note: Any material covering the wall must not exceed 5/8 in. (16 mm).
mounting surface
Attach the left and right TV brackets
(B and C) to the back of the TV using:
The M4/M5 washers (F) and
the M4 x 12 mm (D)
or M5 x 12 mm (H) screws.
Or
The M6/M8 washers (M) and
the M6 x 12 mm (J) screws
or M6 x 20 mm (K) screws
or the M8 x 16 mm (O) screws.
C
a. Locate the studs. Verify the center of the stud with an awl or thin nail or use an
edge-to-edge stud finder.
b. Level the wall plate (A) and mark hole locations.
Thank you for choosing the
Rocketfish RF-TVMLPT03.
The RF-TVMLPT03 TV mount
is designed to support
a TV weighing up to
c. Drill pilot holes as illustrated.
d. Align the wall plate (A) with the pilot holes, then place the washers (T) over the holes.
Insert the lag bolts (U) through the washers, then tighten the lag bolts with a socket wrench
only until the washers are pulled firmly against the wall plate.
DO NOT over-tighten the lag bolts.
130 lbs. (59 kg)
B
or
C
a.
F
M
or
B
< 16 mm
(5⁄8 in.)
Package contents
A Wall plate (1)
B LeftTV bracket (1)
C RightTV bracket (1)
D H
16 - 24 in.
J K
O
406mm - 610mm
b.
B
M4 bag
C
D M4 x 12 mm screws (4)
E M4 x 30 mm screws (4)
A
F M4/M5 washers (8)
G M4/M5 spacers (4)
M5 bag
Option 2: Attaching to a curved or
irregular mounting surface
Attach the left and right TV brackets (B and C) to the
back of the TV using:
The M4/M5 spacers (G), M4/M5 washers (F), and
the M4 x 30 mm screws (E) or M5 x 30 mm screws (I).
Or
The M6/M8 spacers (N), M6/M8 washers (M),
and the M6 x 35 mm screws (L)
or the M8 x 40 mm (P) or M8 x 60 mm screws(Q).
Note: Use the M4 washers (F) between
the spacers and the bracket with the M4
A
H M5 x 12 mm screws (4)
I M5 x 30 mm screws (4)
M4 bag
E
I
F
c.
D
G
M6 bag
J M6 x 12 mm screws (4)
K M6 x 20 mm screws (4)
L M6 x 35 mm screws (4)
M M6/M8 washers (4)
N M6/M8 spacers (4)
C
M4 x 12mm
M4 x 30mm
M4/M5
M4/M5
M5 bag
H
M8 bag
M5 x 12mm
M5 x 30mm
d.
O M8 x 16 mm screws (4)
P M8 x 40 mm screws (4)
Q M8 x 60 mm screws (4)
M6 bag
N
75mm
3 in.
M
L
K
J
or M5 screws only.
Hex key bag
R 3⁄16 in. Hex Key (1)
M6 x 12mm
M6 x 20mm
M6 x 35mm
M6/M8
M6/M8
Hex key bag
M8 bag
P
Q
Lag bolt bag
O
B
R
F
or
F
S Concrete anchors (4)
T Lag bolt washers (4)
M
3/16 in.
T
M8 x 16mm
M8 x 40mm
M8 x 60mm
E I
U
U 5⁄16 in. x 23⁄4 in. lag bolts (4)
L P
Q
Lag bolt bag
Tools you will need:
S
•Phillipsscrewdriver
T
or
G
N
• Stud finder
• Awl
•Hammer(ConcreteOnly)
•½in. socketwrench
• Pencil
B
C
•3/16in. wooddrillbit
•3/8in. masonrydrillbit(ConcreteOnly)
•Powerdrill
U
• Level
• Tape measure
in. x 2 in.
|