Schneider Electric Drums VSE 002 User Guide

VSE 002  
RS-485 module  
Publication version: VVSE2/EN M/B006  
User manual  
 
1 General  
VSE 002 External RS-485 Module  
1.  
General  
External RS-485 Module VSE 002 is used to connect VAMP  
protection relays to a RS-485 bus.  
Additionally this module can be used with any device, which has a  
RS-232 or TTL serial interface, when an RS-485 interface is  
required.  
2.  
3.  
Power supply  
The power for the module is taken from pin 9 of the D-connector or  
from an external power supply interface. There is a screw terminal  
(X1, see figure 1) for connecting an external +9...12Vdc power  
supply.  
Module interface to the VAMP  
relays or master device  
The physical interface to the device is a 9-pin D-connector. The  
signal levels may be either TTL or RS-232.  
The TTL/RS-232 interface of the modules is:  
Pin number  
TTL mode  
-
RS-232 mode  
-
1
2
3
4
5
6
7
8
9
RXD (in)  
TXD (out)  
RTS (in)  
RXD (in)  
TXD (out)  
RTS (in)  
GND  
GND  
+8V (in)  
+8V (in)  
The active state of the RTS signal is positive  
voltage (> +3V) in both TTL and RS-232 modes.  
VVSE2/EN M/B006  
3
 
     
4 RS-485 interface  
VSE 002 External RS-485 Module  
4.  
RS-485 interface  
The RS-485 interface supports 2-wire connection. The dip switch  
S1 is used to switch the termination and signal biasing resistors on  
or off.  
Termination  
ON  
OFF  
Interface type  
TTL  
RS-232  
Figure 1. Dipswitch positions of VSE 002  
The direction control of the RS-485 transceiver is done with the  
RTS signal or automatically. The automatic direction control turns  
the transceiver to transmit mode after detecting the falling edge of  
a 0-bit. The direction is kept in transmit mode for 0,5ms. This  
enables the use of the automatic mode with 9,6 kb/s and 19.2 kb/s  
speeds. When the transceiver is changed to receive mode, the  
RS-485 line changes state to logic 1 state due to the biasing  
resistors.  
VVSE2/EN M/B006  
4
 
 
VSE 002 External RS-485 Module  
5 Module layout  
5.  
Module layout  
Figure 2. Component layout  
6.  
Module mounting  
Figure 3. Mounting picture of module  
VVSE2/EN M/B006  
5
 
   
7 Module connection to a PC  
VSE 002 External RS-485 Module  
7.  
Module connection to a PC  
The module can be used with a PC, the required cable is  
described in figure 4. When used with a PC an external power  
supply is needed (e.g. type Phoenix Contact 100 240 AC/10-15  
DC/2, Order-No. 29 83 75 6).  
PC serial interface  
VSE 002  
Function  
Pin  
Pin  
Function  
number  
number  
CD (in)  
1
2
3
1
2
3
-
RXD (in)  
RXD (in)  
TXD  
(out)  
TXD  
(out)  
DTR  
(out)  
4
4
RTS (in)  
GND  
5
6
7
5
6
7
-
DSR (in)  
-
RTS  
(out)  
GND  
CTS (in)  
-
8
9
8
9
-
+8V (in)  
Figure 4. PC interface cable  
8.  
Ordering codes  
VSE 002  
RS-485interfacemodule  
VVSE2/EN M/B006  
6
 
   
 
Customers Care Center  
Schneider Electric  
35 rue Joseph Monier  
92506 Rueil-Malmaison  
FRANCE  
Phone: +33 (0) 1 41 29 70 00  
Fax: +33 (0) 1 41 29 71 00  
Publication version: VVSE2/EN M/B006  
Publishing: Schneider Electric  
02/2013  
 

Quasar Camcorder VM D100 User Guide
Raritan Engineering DVD VCR Combo 255 80 6030 User Guide
RCA Camcorder EZ1100 User Guide
Rosewill Switch RHUB 200 User Guide
Rosle Cookware 95030 User Guide
Rowenta Iron DX1900 User Guide
RoyalTek GPS Receiver RTG 2000 User Guide
Sanyo CRT Television DS31520 User Guide
Satco Products Work Light PAR16 User Guide
Sears Automobile Battery Charger 2871225 User Guide